Website: www.OzoneSolutions.com
Email: support@ozonesolutions.com
Phone: (712) 439-6880
Hours: 8 AM - 5 PM Central Time

High Purity - Wine and Beverage Grade Polythersulfone (PES)

 
Request Information
* Required Name * Email * Phone Application / Industry Details *
Rental Systems May Be Available

Wine and Beverage Grade PES cartridges remove all yeast and significantly reduce microorganisms prior to wine and beverage bottling. The removal of spoilage organisms is of critical importance. By incorporating a polypropylene prefiltration stage, Ozone Solutions' GBPES series filter cartridges provide exceptional retention of these organisms, while delivering long service life. Each cartridge is flushed to 18 megohlm with high purity water and 100% integrity tested to ensure the delivery of clean effluent as well as low extractables.

Construction Materials

Membrane...........................Polyethersulfone
Support Media ..............................Polypropylene
Prefilter.............................................Polypropylene
End Caps...........................................Polypropylene
Cages and Cores ...........................Polypropylene
O-Rings/Gaskets.............Buna, EPDM, Silicone, Viton®, Teflon® Encapsulated Viton®

Sanitization/Sterilization

Filtered Hot Water............................88°C at 5 PSI
Steam Sterilization:
121°C for 30 min. (@ 2 PSI up to 40 cycles)
121°C for 60 min. (@ 2 PSI up to 25 cycles)
Chemicals: Peracetic acid, chlorinated alkaline products, bleach, sulfur dioxide and hydrogen peroxide at typical sanitization concentrations and temperatures.
Note: Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized.

Maximum Recommended Operating Conditions

Temperature........................................176°F (80°C)

Dimensions

Length: 10 to 40 inches (25.4 to 101.6 cm) nominal
Outside Diameter: 2.70 inches (7.0 cm) nominal

Maximum Differential Pressures

Forward............................. 50 PSI (3.4 bar) at 20°C
Reverse.............................. 40 PSI (2.7 bar) at 20°C

FDA Listed Materials

Manufactured from materials which are listed for food contact applications in Title 21 of the U.S. Code of Federal Regulations.

Toxicity

All polypropylene components meet the specifications for biological safety per USP Class VI - 121°C for plastics.

DISCLAIMER: Filtration data presented is representative of performance observed in controlled laboratory testing. It is not given as a warranty, specification or statement of fitness for use. Specific performance can vary widely depending on contaminant type, fluid properties, flow rates and environmental conditions. It is recommended that users conduct thorough qualification testing to assure the product functions as required.

Cartridge Options
Rating (µ)LengthEnd Cap StyleO-Rings/GasketsAdders
0.210” (25.4 cm)DOE Flat GasketBunaStainless Steel Insert
0.4520” (50.8 cm)222 w/ FinEPDM316ss Compression Spring
0.6530” (76.2 cm)222 w/ Flat CapSilicone
40” (101.6 cm)226 w/ Flat CapViton®
226 w/ FinTeflon® Encapsulated Viton®
Teflon® Encapsulated Silicone

DISCLAIMER: Filtration data presented is representative of performance observed in controlled laboratory testing. It is not given as a warranty, specification or statement of fitness for use. Specific performance can vary widely depending on contaminant type, fluid properties, flow rates and environmental conditions. It is recommended that users conduct thorough qualification testing to assure the product functions as required.

The above information is from http://www.OzoneSolutions.com and is copyrighted by Ozone Solutions Inc.
Jump To TopOzone Solutions Inc. | (712) 439-6880Jump To Top

8 AM - 5 PM Central Time
Phone: (712) 439-6880
Toll Free: (888) 892-0303 (USA Only)
Fax: (712) 439-6733
Email: support@ozonesolutions.com
CLOSE WINDOW