Website: www.OzoneSolutions.com
Email: support@ozonesolutions.com
Phone: (712) 439-6880
Hours: 8 AM - 5 PM Central Time

High Purity - Pharmaceutical Grade Polyethersulfone (PES)

 
Request Information
* Required Name * Email * Phone Application / Industry Details *
Rental Systems May Be Available

PPES Pharmaceutical Grade filter cartridges are ideal for sterile filtration and clarification of pharmaceutical and biological solutions. Each PPES cartridge is integrity tested during manufacturing and is supported by a validation guide for regulatory compliance. Low protein binding and the broad chemical compatibility characteristics of the polyethersulfone membrane, along with exceptional flow rate vs pressure drop, makes the PPES series the ideal choice for a variety of valuable and/or critical pharmaceutical solutions.

PPES cartridges are fully validated as sterilizing grade filters in accordance with HIMA and ASTM F838-05 guidelines. Sterile effluent was achieved with challenge concentration levels in excess of 107 Brevundimonas diminuta organisms per cm2 of filter area.

Construction Materials

Membrane..................................Polyethersulfone
Support Media ..............................Polypropylene
End Caps...........................................Polypropylene
Center Core .....................................Polypropylene
Outer Support Cage....................Polypropylene
O-Rings/Gaskets.............Buna, EPDM, Silicone, Viton®, Teflon® Encapsulated Viton®

Sterilization

Hot Water...... 85°- 95°C, 30 min., max. pressure drop 7 psi
In-Line Steaming......................... 134°C, 30 min., max. pressure drop 7 psi; 100 cycles

Dimensions

Length: 10 to 40 inches (25.4 to 101.6 cm) nominal
Outside Diameter: 2.70 inches (7.0 cm) nominal

Maximum Recommended Operating Conditions

Temperature....................................... 176°F (80°C)
Forward....................72 PSI (5 bar) at 68°F (20°C), 29 PSI (2 bar) at 176°F (80°C)
Reverse.................................................29 PSI (2 bar)

Toxicity

All polypropylene components meet the specifications for biological safety per USP Class VI - 121°C for plastics.

FDA Listed Materials

Manufactured from materials which are listed for food contact applications in Title 21 of the U.S. Code of Federal Regulations.

DISCLAIMER: Filtration data presented is representative of performance observed in controlled laboratory testing. It is not given as a warranty, specification or statement of fitness for use. Specific performance can vary widely depending on contaminant type, fluid properties, flow rates and environmental conditions. It is recommended that users conduct thorough qualification testing to assure the product functions as required.

Rating (µ)Length, NominalEnd Cap StyleO-Rings/Gaskets
0.210” (25.4 cm)DOE Flat GasketBuna-N
20” (50.8 cm)222 w/ FinEPDM
30” (76.2 cm)222 w/ Flat CapSilicone
40” (101.6 cm)226 w/ Flat CapViton®
226 w/ FinTeflon® Encapsulated Viton®
Teflon® Encapsulated Silicone

DISCLAIMER: Filtration data presented is representative of performance observed in controlled laboratory testing. It is not given as a warranty, specification or statement of fitness for use. Specific performance can vary widely depending on contaminant type, fluid properties, flow rates and environmental conditions. It is recommended that users conduct thorough qualification testing to assure the product functions as required.

The above information is from http://www.OzoneSolutions.com and is copyrighted by Ozone Solutions Inc.
Jump To TopOzone Solutions Inc. | (712) 439-6880Jump To Top

8 AM - 5 PM Central Time
Phone: (712) 439-6880
Toll Free: (888) 892-0303 (USA Only)
Fax: (712) 439-6733
Email: support@ozonesolutions.com
CLOSE WINDOW