Website: www.OzoneSolutions.com
Email: support@ozonesolutions.com
Phone: (712) 439-6880
Hours: 8 AM - 5 PM Central Time

High Purity - General Grade PTFE

 
Request Information
* Required Name * Email * Phone Application / Industry Details *
Rental Systems May Be Available

General Grade PTFE Cartridges are designed for multi-purpose use wherever a cost effective PTFE membrane cartridge is required. GGPTFE series cartridges are hydrophobic and resist wetting in critical air/vent applications. Priced well below special purpose PTFE membrane cartridges, General Grade PTFE cartridges are still manufactured with the same careful attention to quality and performance.

The Extended Area option (GGPTFEX) offers up to 40% more surface area. This additional area results in significant increases in flowrate and loading capacity in the same footprint.

Construction Materials

Membrane......................................................Teflon®
Support Media ..............................Polypropylene
End Caps...........................................Polypropylene
Center Core .....................................Polypropylene
Outer Support Cage....................Polypropylene
O-Rings/Gaskets.............Buna, EPDM, Silicone, Viton®, Teflon® Encapsulated Viton®

Sanitization/Sterilization

Filtered Hot Water..................... 80°C for 30 min.
Steam Sterilization................121°C for 30 min., multiple cycles
Chemicals: Cartridges are chemically compatible with most chemicals and sanitizing agents.
Note: Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized.

Dimensions

Length: 10 to 40 inches (25.4 to 101.6 cm) nominal
Outside Diameter: 2.70 inches (7.0 cm) nominal

Maximum Differential Pressures

Forward............................. 50 PSI (3.4 bar) at 20°C
Reverse.............................. 40 PSI (2.7 bar) at 20°C

FDA Listed Materials

Manufactured from materials which are listed for food contact applications in Title 21 of the U.S. Code of Federal Regulations.

Toxicity

All components meet the specifications for biological safety per USP Class VI - 121°C for plastics.

DISCLAIMER: Filtration data presented is representative of performance observed in controlled laboratory testing. It is not given as a warranty, specification or statement of fitness for use. Specific performance can vary widely depending on contaminant type, fluid properties, flow rates and environmental conditions. It is recommended that users conduct thorough qualification testing to assure the product functions as required.

Rating (µ)LengthEnd Cap StyleO-Rings/GasketsAdders
0.110” (25.4 cm)DOE Flat GasketBunaStainless Steel Insert
0.220” (50.8 cm)222 w/ FinEPDM316ss Compression Spring
0.4530” (76.2 cm)222 w/ Flat CapSilicone
40” (101.6 cm)226 w/ Flat CapViton®
226 w/ FinTeflon® Encapsulated Viton®
213 Internal O-RingTeflon® Encapsulated Silicone

DISCLAIMER: Filtration data presented is representative of performance observed in controlled laboratory testing. It is not given as a warranty, specification or statement of fitness for use. Specific performance can vary widely depending on contaminant type, fluid properties, flow rates and environmental conditions. It is recommended that users conduct thorough qualification testing to assure the product functions as required.

The above information is from http://www.OzoneSolutions.com and is copyrighted by Ozone Solutions Inc.
Jump To TopOzone Solutions Inc. | (712) 439-6880Jump To Top

8 AM - 5 PM Central Time
Phone: (712) 439-6880
Toll Free: (888) 892-0303 (USA Only)
Fax: (712) 439-6733
Email: support@ozonesolutions.com
CLOSE WINDOW