Website: www.OzoneSolutions.com
Email: support@ozonesolutions.com
Phone: (712) 439-6880
Hours: 8 AM - 5 PM Central Time

High Purity - Electronics Grade Nylon 6,6 and Plus+ Nylon 6,6

 
Request Information
* Required Name * Email * Phone Application / Industry Details *
Rental Systems May Be Available

Electronics Grade Nylon 6,6 Cartridges are designed to meet the special needs of the electronics and high purity chemical industries. GEHNY cartridges are available in both standard and Plus+ grades. The Plus+ grade membrane is modified with a highly positive charge; allowing for the removal of particles that are significantly smaller than the membrane's rating. Each cartridge is flushed to 18 megohlms with UPW and 100% integrity tested to deliver ultraclean effluent as well as ultra-low extractables. The Extended Area option (GEHNYX) offers up to 40% more surface area. This additional area results in significant increases in flowrate and loading-capacity in the same footprint.

Construction Materials

Membrane.................................................Nylon 6,6
Support Media ..............................Polypropylene
End Caps...........................................Polypropylene
Center Core .....................................Polypropylene
Outer Support Cage....................Polypropylene
O-Rings/Gaskets.............Buna, EPDM, Silicone, Viton®, Teflon® Encapsulated Viton®

Sanitization/Sterilization

Filtered Hot Water..................... 80°C for 30 min.
Steam Sterilization................121°C for 30 min., multiple cycles
Chemicals: Cartridges are chemically compatible with most chemicals and sanitizing agents.
Note: Stainless steel insert option needed for all cartridges being hot water sanitized or steam sterilized.

Dimensions

Length: 10 to 40 inches (25.4 to 101.6 cm) nominal
Outside Diameter: 2.70 inches (7.0 cm) nominal

Maximum Differential Pressures

Forward............................. 50 PSI (3.4 bar) at 20°C
Reverse.............................. 40 PSI (2.7 bar) at 20°C

FDA Listed Materials

Manufactured from materials which are listed for food contact applications in Title 21 of the U.S. Code of Federal Regulations.

Toxicity

All polypropylene components meet the specifications for biological safety per USP Class VI - 121°C for plastics.

DISCLAIMER: Filtration data presented is representative of performance observed in controlled laboratory testing. It is not given as a warranty, specification or statement of fitness for use. Specific performance can vary widely depending on contaminant type, fluid properties, flow rates and environmental conditions. It is recommended that users conduct thorough qualification testing to assure the product functions as required.

Cartridge Options
Rating (µ)LengthEnd Cap StyleO-Ring/GasketsAdders
0.0310” (25.4 cm)DOE Flat GasketBunaStainless Steel Insert
0.0520” (50.8 cm)222 w/ FinEPDM316ss Compression Spring
0.130” (76.2 cm)222 w/ Flat CapSilicone
0.240” (101.6 cm)226 w/ Flat CapViton®
0.45226 w/ FinTeflon® Encapsulated Viton®
0.65213 Internal O-RingTeflon® Encapsulated Silicone
0.8
1.2

DISCLAIMER: Filtration data presented is representative of performance observed in controlled laboratory testing. It is not given as a warranty, specification or statement of fitness for use. Specific performance can vary widely depending on contaminant type, fluid properties, flow rates and environmental conditions. It is recommended that users conduct thorough qualification testing to assure the product functions as required.

The above information is from http://www.OzoneSolutions.com and is copyrighted by Ozone Solutions Inc.
Jump To TopOzone Solutions Inc. | (712) 439-6880Jump To Top

8 AM - 5 PM Central Time
Phone: (712) 439-6880
Toll Free: (888) 892-0303 (USA Only)
Fax: (712) 439-6733
Email: support@ozonesolutions.com
CLOSE WINDOW